secure boot- Can't mount root filesystem. Was: Problem with dracut-modules-olpc-0.2.4

[Esteban Bordón]

Hi Daniel,

I'm testing secure boot in F11-XO1 (os10).

When XO boots in secure boot the lease file doesn't read from USB key. I
disabled the activation in dracut and I reinstalled dracut-olpc-modules and
kernel and I signed them.

This log is displayed when I turn on the XO:

[    2.907314] brd: module loaded
[    2.920838] NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND
512MiB 3,3V 8-bit)
[    2.931270] 2 NAND chips detected
[    2.947938] cmdlinepart partition parsing not available
[    2.954239] Searching for RedBoot partition table in NAND 512MiB 3,3V
8-bit at offset 0x0
[    2.970343] No RedBoot partition table detected in NAND 512MiB 3,3V 8-bit
[    2.996908] serio: i8042 KBD port at 0x60,0x64 irq 1
[    3.002587] serio: i8042 AUX port at 0x60,0x64 irq 12
[    3.015428] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[    3.023061] rtc0: alarms up to one year, y3k, 242 bytes nvram
[    3.042876] olpc-dcon:  Discovered DCON version 2
[    3.063808] Linux video capture interface: v2.00
[    3.153404] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input4
[    3.176771] geode-mfgpt:  Registered timer 1
[    3.196556] cpuidle: using governor ladder
[    3.214714] cpuidle: using governor menu
[    3.233455] sdhci: Secure Digital Host Controller Interface driver
[    3.254585] sdhci: Copyright(c) Pierre Ossman
[    3.274389] sdhci-pci 0000:00:0c.1: SDHCI controller found [11ab:4101]
(rev 10)
[    3.298023] sdhci-pci 0000:00:0c.1: enabling device (0000 -> 0002)
[    3.320869] sdhci-pci 0000:00:0c.1: Invalid iomem size. You may
experience problems.
[    3.347109] Registered led device: mmc0::
[    3.369713] sdhci_set_ios: power off for mmc0 from c05edf11
[    3.393872] mmc0: SDHCI controller on PCI [0000:00:0c.1] using DMA
[    3.419604] sdhci_set_power: new power value = 14
[    3.451202] Error allocating fallback algo aes
[    3.475808] alg: cipher: Failed to load transform for geode-aes: -2
[    3.506283] sdhci_set_ios: power off for mmc0 from c05edf11
[    3.512867] sdhci_set_power: new power value = 0
[    3.573197] Error allocating fallback algo ecb(aes)
[    3.599878] alg: skcipher: Failed to load transform for ecb-aes-geode: -2
[    3.628861] geode-aes: GEODE AES engine enabled.
[    3.658194] Advanced Linux Sound Architecture Driver Version 1.0.20.
[    3.691906] Failure reading codec reg 0x7e,Last value=0x7e805368
[    3.720509] Failure reading codec reg 0x7e,Last value=0x7e805368
[    3.760685] ALSA device list:
[    3.785201]   #0: CS5535 Audio cs5535audio at 0x1480, irq 5
[    3.813040] TCP bic registered
[    3.836955] Initializing XFRM netlink socket
[    3.862716] NET: Registered protocol family 10
[    3.889465] lo: Disabled Privacy Extensions
[    3.914247] Mobile IPv6
[    3.936307] NET: Registered protocol family 17
[    3.967423] Freeing unused kernel memory: 236k freed
[    3.993617] Write protecting the kernel text: 2748k
[    4.018837] Write protecting the kernel read-only data: 860k
[    4.304065] udev: starting version 141
[    5.249895] usbcore: registered new interface driver usbfs
[    5.329162] usbcore: registered new interface driver hub
[    5.482006] usbcore: registered new device driver usb
[    5.640157] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.792094] ehci_hcd 0000:00:0f.5: EHCI Host Controller
[    5.831828] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.985996] ehci_hcd 0000:00:0f.5: new USB bus registered, assigned bus
number 1
[    6.190320] ehci_hcd 0000:00:0f.5: irq 10, io mem 0xfe01b000
[    6.310419] ehci_hcd 0000:00:0f.5: USB 2.0 started, EHCI 1.00
[    6.470063] usb usb1: configuration #1 chosen from 1 choice
[    6.477142] hub 1-0:1.0: USB hub found
[    6.477296] hub 1-0:1.0: 4 ports detected
[    6.478027] ohci_hcd 0000:00:0f.4: OHCI Host Controller
[    6.478143] ohci_hcd 0000:00:0f.4: new USB bus registered, assigned bus
number 2
[    6.478281] ohci_hcd 0000:00:0f.4: irq 10, io mem 0xfe01a000
[    6.479896] modprobe used greatest stack depth: 2580 bytes left
[    6.761140] usb usb2: configuration #1 chosen from 1 choice
[    6.762237] hub 2-0:1.0: USB hub found
[    6.762333] hub 2-0:1.0: 4 ports detected
[    7.050043] usb 1-1: new high speed USB device using ehci_hcd and address
2
[    7.099360] mount used greatest stack depth: 2492 bytes left
[    7.266896] usb 1-1: configuration #1 chosen from 1 choice
[    7.320473] lib80211: common routines for IEEE802.11 drivers
[    7.440085] usb 1-1: firmware: requesting usb8388.bin
[    8.213968] usb8xxx: Firmware ready event received
[    8.235737] libertas: 00:17:c4:0c:d8:34, fw 5.110.22p23, cap 0x000003a3
[    8.279072] libertas: eth0: Marvell WLAN 802.11 adapter
[    8.281592] libertas: PREP_CMD: command 0x0074 failed: 2
[    8.281613] usb8xxx: Firmware does not seem to support PS mode
[    8.287666] usbcore: registered new interface driver usb8xxx

mount: you must specify the filesystem type

Can't mount root filesystem

Boot has failed, sleepeng forever


Thanks for any help.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.laptop.org/pipermail/devel/attachments/20091217/397ef9db/attachment.html>