[Testing] [support-gang] Lost Communication in 10.1.3?

[Samuel Greenfeld]

The XO-1 will only see Ad-hoc XO-1.5 networks which currently have XOs 
connected to them.  It will not show all three Mayan icons unless there 
is an XO-1.5 or other computers creating three Ad-hoc networks, one with 
each of the desired names.

You will have to manually connect the XO-1 to an Ad-hoc network; it will 
not automatically do so.

Unless you told them otherwise, by default all the XO-1.5s likely 
decided to use Ad-hoc channel 1 if they did not see a preferred access 
point, so you should go looking on the 10.1.3 XO-1 for a filled color 
circle with a single dot in it.  If the XO-1.5s were near an access 
point they were taught about, they may have connected to that instead.  
The ad-hoc networks on the XO-1 with 10.1.3 will look like the 
filled-color (active) networks on the XO-1.5 using the XO-1 user's 
colors to indicate that someone is listening on the channel.

It may take up to 30 or 60 seconds(?) from the time that an XO-1.5 
created the Ad-hoc network to the point that an XO-1 will decide to 
rescan to see what networks are out there.  I'm hoping there are no 
restrictions on rescanning once an XO-1 decides to connect to a Mesh 
network.

Admittedly the graphic 
http://wiki.sugarlabs.org/go/File:Adhoc_network_XO-1.png (available from 
http://wiki.sugarlabs.org/go/Features/Ad_hoc_Networking) is someone 
confusing, since the XO-1 in that screenshot actually is connected {has 
parenthesis} to a network which is neither the Ad-hoc network spotted 
(on channel 11 - a dot and two lines) nor the Mesh ones.



On 2/6/2011 12:58 PM, Caryl Bigenho wrote:
> OK I think I know what happened.  First a question... how will the ad 
> hoc networks look on the XO-1?  They were still targets on these.  
> Maybe I grabbed the wrong usb stick and put 10.1.2 on them again... 
> but I don't think so.
>
> I didn't see any parenthesis... just that the 2 XO-1s could see each 
> other fine, but they couldn't see the 1.5s, even with sharing on.  I 
> started the Chat on a 1.5.  Maybe it has to start on a 1.0?
>
> Caryl
>
> > Date: Sun, 6 Feb 2011 12:52:01 -0500
> > Subject: Re: [Testing] [support-gang] Lost Communication in 10.1.3?
> > From: gerald.ardito at gmail.com
> > To: cbigenho at hotmail.com
> > CC: gerald.ardito at gmail.com; support-gang at lists.laptop.org; 
> devel at lists.laptop.org; testing at lists.laptop.org; support-gang at laptop.org
> >
> > Caryl,
> >
> > Once you connect to one of the ad-hoc networks, you will see the
> > familiar parentheses surrounding it. Then, in the Neighborhood View on
> > the the XOs, this network should appear as a wireless device.
> >
> > I would start troubleshooting by going o Settings and turning the
> > radio off and then on again.
> >
> > Good luck.
> >
> > Gerald
> >
> > On Sunday, February 6, 2011, Caryl Bigenho <cbigenho at hotmail.com> wrote:
> > >
> > >
> > >
> > >
> > >
> > > Hi Gerald,
> > >
> > > That was the first thing I tried and it didn't work for me.  I'll 
> try it again when I get back from TX.  How did you connect the 1.0 to 
> the network?  They are still showing as access points rather than the 
> Mayan numerals on the 1.0s.  Maybe I need to do the install again.
> > >
> > > Caryl
> > >
> > >> Date: Sun, 6 Feb 2011 11:39:38 -0500
> > >> From: gerald.ardito at gmail.com
> > >> To: support-gang at lists.laptop.org
> > >> CC: devel at lists.laptop.org; testing at lists.laptop.org; 
> support-gang at laptop.org
> > >> Subject: Re: [Testing] [support-gang] Lost Communication in 10.1.3?
> > >>
> > >> Caryl,
> > >>
> > >> I have been able to make this work. Here's what I did:
> > >> 1. Create an ad-hoc network on one of the 1.5s.
> > >> 2. Connect to it on the 1.0s.
> > >> 3. Open Chat and make public.
> > >>
> > >> Hope this helps.
> > >> Gerald
> > >>
> > >> On Sunday, February 6, 2011, Caryl Bigenho <cbigenho at hotmail.com> 
> wrote:
> > >> >
> > >> >tee's what I
> > >> >
> > >> >
> > >> >.
> > >>
> > >> H
> > >> > Hi...
> > >> >
> > >> > Prepping some XOs for our booth at SCaLE 9X Feb 26-27.  When I 
> first started charging and testing I was running 10.1.2.  I tried Chat 
> and found that the XO-1s could easily chat with the XO-1.5s.
> > >> >
> > >> > Then I updated all of them to 10.1.3, and this ability seems to 
> have been lost.  While the XO-1.5s connected right away to the ad hoc 
> network, the XO-1s were totally left out.  They can only see each other.
> > >> >
> > >> > Is this an intentional change?  Is there a way for both models 
> to communicate among themselves in 10.1.3?
> > >> >
> > >> > Caryl
> > >> >
> > >> _______________________________________________
> > >> Testing mailing list
> > >> Testing at lists.laptop.org
> > >> http://lists.laptop.org/listinfo/testing
> > >
> > >
>
>
> _______________________________________________
> Devel mailing list
> Devel at lists.laptop.org
> http://lists.laptop.org/listinfo/devel

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.laptop.org/pipermail/testing/attachments/20110206/ab7579c3/attachment.htm