Linux version 2.6.17-1.2396.fc6 (brewbuilder@ls20-bc2-14.build.redhat.com) (gcc version 4.1.1 20060711 (Red Hat 4.1.1-7)) #1 SMP Thu Jul 13 20:38:41 EDT 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000073b0000 (usable) BIOS-e820: 00000000073b0000 - 00000000073bffc0 (ACPI data) BIOS-e820: 00000000073bffc0 - 00000000073c0000 (ACPI NVS) BIOS-e820: 0000000040400000 - 0000000040440004 (reserved) BIOS-e820: 00000000f0000000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 115MB LOWMEM available. Using x86 segment limits to approximate NX protection On node 0 totalpages: 29616 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 25520 pages, LIFO batch:7 DMI not present or invalid. Using APIC driver default ACPI: RSDP (v000 OID_00 ) @ 0x000e9010 ACPI: RSDT (v001 AMD RSDT_000 0x31303030 AMD 0x31303030) @ 0x073b20d0 ACPI: FADT (v001 AMD FACP_000 0x31303030 AMD 0x31303030) @ 0x073b1fd0 ACPI: BOOT (v001 AMD BOOT_000 0x31303030 AMD 0x31303030) @ 0x073b2060 ACPI: DBGP (v001 AMD DBGP_000 0x31303030 AMD 0x31303030) @ 0x073b2090 ACPI: DSDT (v001 INSYDE GEODE GX 0x00001007 INTL 0x20030122) @ 0x00000000 ACPI: acpi=force override ACPI: PM-Timer IO Port: 0x9c10 Allocating PCI resources starting at 50000000 (gap: 40440004:afbbfffc) Detected 365.265 MHz processor. Built 1 zonelists. Total pages: 29616 Kernel command line: ro quiet vga=0x311 video=vesafb:ypan selinux=0 console=tty0 root=/dev/sda1 acpi=force No local APIC present or hardware disabled mapped APIC to ffffd000 (010f2000) Initializing CPU#0 CPU 0 irqstacks, hard=c080b000 soft=c07eb000 PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x25 Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar ... MAX_LOCKDEP_SUBCLASSES: 8 ... MAX_LOCK_DEPTH: 30 ... MAX_LOCKDEP_KEYS: 2048 ... CLASSHASH_SIZE: 1024 ... MAX_LOCKDEP_ENTRIES: 8192 ... MAX_LOCKDEP_CHAINS: 8192 ... CHAINHASH_SIZE: 4096 memory used by lock dependency info: 696 kB per task-struct memory footprint: 1200 bytes Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 109540k/118464k available (2120k kernel code, 8380k reserved, 1109k data, 240k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 734.64 BogoMIPS (lpj=1469296) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0080a13d c0c0a13d 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0080a13d c0c0a13d 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 16K (32 bytes/line), D cache 16K (32 bytes/line) CPU: After all inits, caps: 0080a13d c0c0a13d 00000000 00000000 00000000 00000000 00000000 Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 16k freed ACPI: Core revision 20060707 ACPI: setting ELCR to 0200 (from 0c20) CPU0: NSC Geode(TM) Integrated Processor by National Semi stepping 02 SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs sizeof(vma)=84 bytes sizeof(page)=32 bytes sizeof(inode)=568 bytes sizeof(dentry)=160 bytes sizeof(ext3inode)=804 bytes sizeof(buffer_head)=52 bytes sizeof(skbuff)=172 bytes checking if image is initramfs... it is Freeing initrd memory: 1384k freed PM: Adding info for No Bus:platform NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xff8b7, last bus=0 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing PM: Adding info for acpi:acpi ACPI: PCI Interrupt Link [LNKA] (IRQs *11) ACPI: PCI Interrupt Link [LNKB] (IRQs *5) ACPI: PCI Interrupt Link [LNKC] (IRQs *10) ACPI: PCI Interrupt Link [LNKD] (IRQs *10) ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PM: Adding info for No Bus:pci0000:00 ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 Boot video device is 0000:00:01.1 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] PM: Adding info for pci:0000:00:01.0 PM: Adding info for pci:0000:00:01.1 PM: Adding info for pci:0000:00:0f.0 PM: Adding info for pci:0000:00:0f.2 PM: Adding info for pci:0000:00:0f.3 PM: Adding info for pci:0000:00:0f.4 PM: Adding info for pci:0000:00:0f.5 Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init PM: Adding info for No Bus:pnp0 PM: Adding info for pnp:00:00 PM: Adding info for pnp:00:01 PM: Adding info for pnp:00:02 ACPI Error (dsopcode-0548): Field [JK0L] at 96 exceeds Buffer [NULL] size 32 (bits) [20060707] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.SBF0.MEM_._CRS] (Node c1110444), AE_AML_BUFFER_LIMIT ACPI Error (uteval-0212): Method execution failed [\_SB_.PCI0.SBF0.MEM_._CRS] (Node c1110444), AE_AML_BUFFER_LIMIT pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0c01 PM: Adding info for pnp:00:03 PM: Adding info for pnp:00:04 pnp: PnP ACPI: found 5 devices usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report ACPI Error (dsopcode-0548): Field [JK0L] at 96 exceeds Buffer [NULL] size 32 (bits) [20060707] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.SBF0.MEM_._CRS] (Node c1110444), AE_AML_BUFFER_LIMIT ACPI Error (uteval-0212): Method execution failed [\_SB_.PCI0.SBF0.MEM_._CRS] (Node c1110444), AE_AML_BUFFER_LIMIT PCI: Ignore bogus resource 6 [0:0] of 0000:00:01.1 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 5, 131072 bytes) TCP bind hash table entries: 2048 (order: 4, 65536 bytes) TCP: Hash tables configured (established 4096 bind 2048) TCP reno registered PM: Adding info for platform:pcspkr Simple Boot Flag at 0x3f set to 0x1 apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1154503514.296:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 PM: Adding info for platform:vesafb.0 vesafb: framebuffer at 0x41000000, mapped to 0xc8080000, using 1200k, total 12288k vesafb: mode is 640x480x16, linelength=1280, pages=2 vesafb: protected mode interface info at c000:6db5 vesafb: pmi: set display start = c00c6ddc, set palette = c00c6e88 vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903 cc03 ce03 cf03 d403 d503 da03 1c03 1dac 1eac 1fac ffac vesafb: scrolling: ypan using protected mode interface, yres_virtual=960 vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 80x30 fb0: VESA VGA frame buffer device PM: Adding info for No Bus:pnp1 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 Linux agpgart interface v0.101 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled PM: Adding info for platform:serial8250 PM: Adding info for No Bus:isa RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AMD5536: IDE controller at PCI slot 0000:00:0f.2 AMD5536: chipset revision 1 AMD5536: not 100% native mode: will probe irqs later AMD5536: 0000:00:0f.2 (rev 01) UDMA100 controller AMD5536: neither IDE port enabled (BIOS) Probing IDE interface ide0... Probing IDE interface ide1... ide-floppy driver 0.99.newide usbcore: registered new driver libusual usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: No PS/2 controller found. Probing ports directly. PM: Adding info for platform:i8042 i8042.c: Can't read CTR while initializing i8042. mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI No-Shortcut mode Time: tsc clocksource has been installed. ACPI: (supports S0 S3 S5) Freeing unused kernel memory: 240k freed Write protecting the kernel read-only data: 393k ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:0f.5[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:0f.5 to 64 ehci_hcd 0000:00:0f.5: EHCI Host Controller ehci_hcd 0000:00:0f.5: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0f.5: irq 10, io mem 0xefd00000 ehci_hcd 0000:00:0f.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 PM: Adding info for usb:usb1 PM: Adding info for No Bus:usbdev1.1_ep00 usb usb1: configuration #1 chosen from 1 choice PM: Adding info for usb:1-0:1.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected PM: Adding info for No Bus:usbdev1.1_ep81 PM: Adding info for No Bus:usbdev1.1 USB Universal Host Controller Interface driver v3.0 SCSI subsystem initialized Initializing USB Mass Storage driver... usb 1-2: new high speed USB device using ehci_hcd and address 3 PM: Adding info for usb:1-2 PM: Adding info for No Bus:usbdev1.3_ep00 usb 1-2: configuration #1 chosen from 1 choice PM: Adding info for usb:1-2:1.0 PM: Adding info for No Bus:usbdev1.3_ep81 PM: Adding info for No Bus:usbdev1.3_ep02 PM: Adding info for No Bus:usbdev1.3 libusual: modprobe for usb-storage succeeded, but module is not present usb 1-4: new high speed USB device using ehci_hcd and address 4 PM: Adding info for usb:1-4 PM: Adding info for No Bus:usbdev1.4_ep00 usb 1-4: configuration #1 chosen from 1 choice PM: Adding info for usb:1-4:1.0 PM: Adding info for No Bus:usbdev1.4_ep02 PM: Adding info for No Bus:usbdev1.4_ep83 PM: Adding info for No Bus:usbdev1.4 scsi0 : SCSI emulation for USB Mass Storage devices PM: Adding info for No Bus:host0 usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usbcore: registered new driver usb-storage USB Mass Storage support registered. PM: Adding info for No Bus:target0:0:0 Vendor: USB 2.0 Model: Flash Disk Rev: 1100 Type: Direct-Access ANSI SCSI revision: 00 PM: Adding info for scsi:0:0:0:0 SCSI device sda: 990208 512-byte hdwr sectors (507 MB) sda: Write Protect is off sda: Mode Sense: 43 00 00 00 sda: assuming drive cache: write through SCSI device sda: 990208 512-byte hdwr sectors (507 MB) sda: Write Protect is off sda: Mode Sense: 43 00 00 00 sda: assuming drive cache: write through sda: sda1 sd 0:0:0:0: Attached scsi removable disk sda PM: Adding info for No Bus:target0:0:1 PM: Removing info for No Bus:target0:0:1 PM: Adding info for No Bus:target0:0:2 PM: Removing info for No Bus:target0:0:2 PM: Adding info for No Bus:target0:0:3 PM: Removing info for No Bus:target0:0:3 PM: Adding info for No Bus:target0:0:4 PM: Removing info for No Bus:target0:0:4 PM: Adding info for No Bus:target0:0:5 PM: Removing info for No Bus:target0:0:5 PM: Adding info for No Bus:target0:0:6 PM: Removing info for No Bus:target0:0:6 PM: Adding info for No Bus:target0:0:7 PM: Removing info for No Bus:target0:0:7 usb-storage: device scan complete kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt 0000:00:0f.4[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:0f.4 to 64 ohci_hcd 0000:00:0f.4: OHCI Host Controller ohci_hcd 0000:00:0f.4: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:0f.4: irq 10, io mem 0xeff00000 PM: Adding info for usb:usb2 PM: Adding info for No Bus:usbdev2.1_ep00 usb usb2: configuration #1 chosen from 1 choice PM: Adding info for usb:2-0:1.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected PM: Adding info for No Bus:usbdev2.1_ep81 PM: Adding info for No Bus:usbdev2.1 usb 2-1: new full speed USB device using ohci_hcd and address 2 sd 0:0:0:0: Attached scsi generic sg0 type 0 PM: Adding info for usb:2-1 PM: Adding info for No Bus:usbdev2.2_ep00 usb 2-1: configuration #1 chosen from 1 choice PM: Adding info for usb:2-1:1.0 hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected PM: Adding info for No Bus:usbdev2.2_ep81 PM: Adding info for No Bus:usbdev2.2 Floppy drive(s): fd0 is 1.44M usb 2-1.1: new low speed USB device using ohci_hcd and address 3 PM: Adding info for usb:2-1.1 PM: Adding info for No Bus:usbdev2.3_ep00 usb 2-1.1: configuration #1 chosen from 1 choice PM: Adding info for usb:2-1.1:1.0 input: Darfon USB Combo Keyboard as /class/input/input0 input: USB HID v1.00 Keyboard [Darfon USB Combo Keyboard] on usb-0000:00:0f.4-1.1 PM: Adding info for No Bus:usbdev2.3_ep81 PM: Adding info for usb:2-1.1:1.1 input: Darfon USB Combo Keyboard as /class/input/input1 input: USB HID v1.00 Device [Darfon USB Combo Keyboard] on usb-0000:00:0f.4-1.1 PM: Adding info for No Bus:usbdev2.3_ep82 PM: Adding info for No Bus:usbdev2.3 usb 2-1.2: new low speed USB device using ohci_hcd and address 4 PM: Adding info for usb:2-1.2 PM: Adding info for No Bus:usbdev2.4_ep00 usb 2-1.2: configuration #1 chosen from 1 choice PM: Adding info for usb:2-1.2:1.0 input: Logitech Optical USB Mouse as /class/input/input2 input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:0f.4-1.2 PM: Adding info for No Bus:usbdev2.4_ep81 PM: Adding info for No Bus:usbdev2.4 usb 2-1.4: new full speed USB device using ohci_hcd and address 5 PM: Adding info for usb:2-1.4 PM: Adding info for No Bus:usbdev2.5_ep00 usb 2-1.4: configuration #1 chosen from 1 choice PM: Adding info for usb:2-1.4:1.0 PM: Adding info for No Bus:usbdev2.5_ep81 PM: Adding info for No Bus:usbdev2.5_ep02 PM: Adding info for No Bus:usbdev2.5_ep83 PM: Adding info for No Bus:usbdev2.5 floppy0: no floppy controllers found pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver pegasus 2-1.4:1.0: eth0, ADMtek AN986 "Pegasus" USB Ethernet (evaluation board), 00:50:ba:89:25:b5 usbcore: registered new driver pegasus Floppy drive(s): fd0 is 1.44M floppy0: no floppy controllers found lp: Unknown symbol parport_write lp: Unknown symbol parport_set_timeout lp: Unknown symbol parport_read lp: Unknown symbol parport_register_device lp: Unknown symbol parport_claim_or_block lp: Unknown symbol parport_register_driver lp: Unknown symbol parport_release lp: Unknown symbol parport_claim lp: Unknown symbol parport_unregister_device lp: Unknown symbol parport_unregister_driver lp: Unknown symbol parport_negotiate ACPI: AC Adapter [AC] (on-line) ACPI: Power Button (FF) [PWRF] i2c_ec: Unknown symbol i2c_del_adapter i2c_ec: Unknown symbol i2c_add_adapter ibm_acpi: ec object not found i2c_ec: Unknown symbol i2c_del_adapter i2c_ec: Unknown symbol i2c_add_adapter sbs: Unknown symbol acpi_get_ec_hc md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com EXT3 FS on sda1, internal journal eth0: set allmulti eth0: set allmulti eth0: set allmulti eth0: set allmulti eth0: set allmulti NET: Registered protocol family 10 lo: Disabled Privacy Extensions eth0: set allmulti eth0: set allmulti IPv6 over IPv4 tunneling driver eth0: set allmulti eth0: no IPv6 routers present