using laptop charger

[James Cameron]

Shouldn't be destroyed.

Even if there is an overvoltage condition (beyond 24V), damage should
be constrained to a fuse on motherboard.

Attached microscope photograph taken facing the back of the DC input
connector.  Big white device with marking 3R is the fuse, silk screen
label PF2, replacement should be rated 3A at 125V.

Second set of pads is next, PF1, in parallel, possibly useful if your
fuse is a different shape.

For continued safety, please replace fuse with required rating, not a
nail or copper wire.

On Thu, Dec 12, 2013 at 11:48:21PM +0000, NoiseEHC wrote:
> Thanks for all the answers, I will let you know whether my XO 1.75
> will be destroyed by the Toshiba adapter... :)
> 
> 
> On 11/12/2013 20:29, John Watlington wrote:
> >James is correct about 19V probably not working with an XO-1, but with an XO-1.75/4
> >you should be fine up to 24V.
> >
> >When running with an input voltage higher than 13V, the battery charger on the
> >motherboard runs noticeably hotter.     Still within spec at 19V and 45C ambient,
> >but you might notice the difference in case temperature near the DC input plug
> >if charging an empty battery.
> >
> >Cheers,
> >wad
> >
> >On Dec 11, 2013, at 3:09 PM, James Cameron wrote:
> >
> >>G'day Andrew,
> >>
> >>There is a voltage above which the XO-1 will not charge, which had
> >>been often encountered by people using solar panels.  Along would come
> >>a cold sunny day, with a greater than normal voltage, and the charging
> >>would stop.
> >>
> >>I don't recall the actual voltage (Richard may remember), but I think
> >>it was somewhere near 18V, and it varied slightly between laptops.
> >>
> >>So it might work, or might not.
> >>
> >>Instead of using a resistor, you might use two or three large diodes
> >>in series, each of which will provide a "forward voltage" 0.6V drop.
> >>Pick the diodes based on the maximum current 1.85A (usually double
> >>that), and the power that will be released as heat; P = V x I, where V
> >>is 0.6, and I is not to exceed 1.85A, so 1.11W minimum "power
> >>dissipation".  Place them in a way that does not hold the heat in.
> >>
> >>https://learn.sparkfun.com/tutorials/diodes
> >>
> >>p.s. if you find one diode does what you need, then add another in
> >>case of variation in the supply or laptop.  You might even add a
> >>full-wave bridge rectifier instead of two diodes, that way the input
> >>polarity won't matter.
> >>
> >>On Wed, Dec 11, 2013 at 01:52:54PM +0000, NoiseEHC wrote:
> >>>Hi!
> >>>
> >>>I am thinking about using my laptop's charger instead of the OLPC
> >>>charger in the future as I move a lot and it's getting really
> >>>tiresome to bring both chargers with me. The plan is to create a
> >>>converter plug and use only the laptop's but it has different
> >>>voltage levels.
> >>>
> >>>laptop: TOSHIBA
> >>>part: PA3715U-1ACA
> >>>model: PA-1750-24
> >>>output: 19V - 3.95A
> >>>
> >>>XO-1.75: DARFON
> >>>model: BBOJ-C
> >>>output: 13.5V - 1.85A
> >>>
> >>>So can I plug my XO to the TOSHIBA adapter? The page says that
> >>>11-18V needed, while the laptop's is 19V. Shall I use a resistor to
> >>>drop the voltage or is it unnecessary? Power usage is not an issue
> >>>to me. (BTW I will use the plug from the XO-1's charger, I guess
> >>>that it did not change in the meantime.)
> >>>
> >>>Thanks,
> >>>Andrew
> >>>_______________________________________________
> >>>Devel mailing list
> >>>Devel at lists.laptop.org
> >>>http://lists.laptop.org/listinfo/devel
> >>-- 
> >>James Cameron
> >>http://quozl.linux.org.au/
> >>_______________________________________________
> >>Devel mailing list
> >>Devel at lists.laptop.org
> >>http://lists.laptop.org/listinfo/devel
> 

-- 
James Cameron
http://quozl.linux.org.au/
-------------- next part --------------
A non-text attachment was scrubbed...
Name: XO-1.75-A1-dc-in-fuse.jpg
Type: image/jpeg
Size: 74955 bytes
Desc: not available
URL: <http://lists.laptop.org/pipermail/devel/attachments/20131213/ef58e73a/attachment.jpg>