debxo ohmd error

[Lee Loncosky]

Apologies if this email has already been received to the list once.  I  
had some trouble sending it.  If someone wishes to get these error  
reports sent to another email address please advise otherwise I will  
continue with them here.

Original Email is next But the situation has changed in that the  
blinking power light is blinking now and suspend seems to work  but  
when I hit the power button again to wake it  I get a reset instead.   
I will test a little more.

Original email

I have an error with the ohmd, see below. Things seemed to work with  
pw button although I did not have a blinking power light for some  
reason.  The error may have happened when I closed the lid.  At least  
suspend did not work then either and then I noticed the debug error.


[ohm_conf_set_key_internal] ohm-conf.c:307 (20:55:20):	 set existing  
key 'button.power' : 0
[ohm_conf_set_key_internal] ohm-conf.c:316 (20:55:20):	 emit key- 
changed : button.power
[key_changed_cb] ohm-module.c:94 (20:55:20):	 key changed!  
button.power : 0
[key_changed_cb] ohm-module.c:104 (20:55:20):	 found watched key  
button.power
[key_changed_cb] ohm-module.c:109 (20:55:20):	 notify suspend with id:0
[ohm_plugin_conf_set_key] ohm-plugin.c:162 (21:05:17):	 plugin buttons  
setting key button.lid to 1
[ohm_conf_set_key_internal] ohm-conf.c:307 (21:05:17):	 set existing  
key 'button.lid' : 1
[ohm_conf_set_key_internal] ohm-conf.c:316 (21:05:17):	 emit key- 
changed : button.lid
[key_changed_cb] ohm-module.c:94 (21:05:17):	 key changed!  
button.lid : 1
[key_changed_cb] ohm-module.c:104 (21:05:17):	 found watched key  
button.lid
[key_changed_cb] ohm-module.c:109 (21:05:17):	 notify display with id:2
[ohm_plugin_conf_set_key] ohm-plugin.c:162 (21:05:17):	 plugin display  
setting key backlight.state to 0
[ohm_conf_set_key_internal] ohm-conf.c:307 (21:05:17):	 set existing  
key 'backlight.state' : 0
[ohm_conf_set_key_internal] ohm-conf.c:316 (21:05:17):	 emit key- 
changed : backlight.state
[key_changed_cb] ohm-module.c:94 (21:05:17):	 key changed!  
backlight.state : 0
[key_changed_cb] ohm-module.c:104 (21:05:17):	 found watched key  
backlight.state
[key_changed_cb] ohm-module.c:109 (21:05:17):	 notify dpms with id:0
** (ohmd:2136): DEBUG: Setting DPMS state
The program 'ohmd' received an X Window System error.
This probably reflects a bug in the program.
The error was 'BadMatch (invalid parameter attributes)'.
  (Details: serial 11 error_code 8 request_code 137 minor_code 6)
  (Note to programmers: normally, X errors are reported asynchronously;
   that is, you will receive the error a while after causing it.
   To debug your program, run it with the --sync command line
   option to change this behavior. You can then get a meaningful
   backtrace from your debugger if you break on the gdk_x_error()  
function.)